Sunday, March 18, 2007

Canon A70 - IR Modification

I describe below how to modify a Canon Powershot A70 into an IR only camera by replacing the factory installed IR cut filter with an IR only passing filter.

By removing the IR cut filter, and replacing it with an appropriate filter that only lets IR radiation pass, we can create a highly sensitive, IR capable digital camera that opens up a whole new world of creative possibilities while retaining the convenience of digital photography.

Why did I choose the A70? There are no specific technical reasons, I merely had one at my disposal. This hack is not new and has been performed with numerous different camera models by many other people. However, as decent documentation is scarce, I believe this page might be worthwhile for someone.

Before I continue, a few words of caution. Please read them carefully!

  • The below documentation is for entertainment or educational purposes only. It is most likely incomplete, wrong, misleading, full of errors and omissions, and potentially hazardous to yourself and your environment. Peruse at your own risk.
  • Understand that it is a very likely possibility that your camera will not survive the described modification. Don't attempt this if you don't feel the camera is expendable.
  • The flash capacitor in the camera stores a possibly lethal current. While unlikely, if you have a known or unknown medical condition, or just bad luck, you could possibly kill your self. If you proceed, take the appropriate precautions. The only way to stay completely safe is not to attempt this modification at all.
  • You agree to hold me free of any damages or injuries that should result from you or someone you know attempting the below modification.


You will need as a minimum the following tools and equipment:

  • EquipmentA set of 3 or 4 fine tweezers of various shapes
  • A 1mm flat head screwdriver
  • A Phillips screwdriver #000
  • A TORX screwdriver #T4
  • Packaging tape
  • A permanent pen
  • A clean work area
  • A Cokin P007 IR pass filter or something equivalent to create a replacement for the IR cut filter.
  • A dremel tool or similar to cut the replacement for the IR cut filter to its proper size. A small hand saw can be used as well, with 150 grain sand paper to sand the piece down to final dimensions.

Before you begin, have a good system to keep track of the screws and their original location:
Screw tracking
A large piece of packing or duct tape, turned around to expose the sticky side and fixed to your desk at it's ends is perfect. Draw outlines of the pieces you are removing directly onto the sticky side of the tape, label the drawn parts accordingly, then set down the screws at their approximate locations onto the tape while you disassemble. This will greatly help in preserving all screws and making sure they go back where they belong once you reassemble.

The Modification

First you need to remove the 3 screws on the bottom of the camera.

Open the cover for the connection ports. Remove the tray containing the CR1220 battery. You will see two screws which you need to remove.

Open the battery compartment on the bottom of the camera. There are four screws that need to be removed. Two on top and two on the inside of the compartment.

Open the CF card door and turn the camera on its head. There is another screw that needs to be removed.

Now the top plate containing the zoom and shutter release comes loose. It attaches via a tiny green connector to the body of the camera. Disconnect and remove. The CF card door will now also come off.

On the front of the camera, press the button marked with a red circle. This will allow you to unscrew the silver plastic ring around the lens.

There is one last screw on the back of the camera that you need to remove.

You will now need to carefully pry the plastic shell apart and off of the camera. Remove the back portion covering the LCD screen first, starting at the bottom and working yourself up. You will need to use some force, but not excessively so. It's more a question of feeling.

The cover for the battery compartment can be removed by pushing at the metal axis forming the hinge to the compartment in the direction of the green arrow with something like a paper clip. Watch the spring circled in red, you don't want it to go flying across the room.

This is what you end up with once the lid has been removed.

Now remove the mode dial at the top via the two screws holding it.

Before you proceed, take note of the "huge" capacitor to the left. It temporarily stores the power for a flash discharge and is probably loaded to full capacity. To prevent it from discharging via an accidental touch, possibly seriously hurting or even killing you or frying any equipment you might be touching at the time, I suggest you cover the terminals on top with electrician's tape for insulation.

Next, you need to remove the flexible circuit board covering most of the top and back of the camera. Start by removing the one screw holding it at the bottom.

Next, push the black lever to the top left inwards, so that you can remove the switch registering if the CF card door is open or shut. Be careful you don't push the black lever in too far, or it will come off and you will be hunting for it and the spring that usually pushes it back out. NOTE: this needs to work perfectly again when you put the camera back together. If not, the camera will think the CF card door is open and will NOT turn on. Be careful and take your time.

Now carefully remove the flexible circuit board from the body by lifting it off of the green circled notches one by one.

Once you have pried it completely loose, you will see where it attaches via a connector to one of the main circuit boards. carefully lift the green circled tabs with a small screw driver to unlock the connector and you will be able to pull the flexible circuit board completely off.

Now that the circuit board is removed, you can continue by removing the CF card reader. Remove the single screw circled above. Then, slowly slide the CF reader off of the rest of the body, towards you. You might need to lift it over a tab at the bottom of the camera.

Once it is almost off, separate the connector between the reader and the underlying DIGIC processor board by simply pulling back on it.

This is what it will look like once it has been separated.

Next is the LCD screen. But before you can remove it, you need to remove the optical viewfinder first. There is one screw on the front that you need to remove.

Then there are two more on top. Once removed, you can lift the viewfinder off of the top carefully. Take note that it is snapped in place in front where you removed the first screw. You will need to wiggle a bit for it to pop loose.

Under the area where the viewfinder was you will find the first screw that holds the LCD panel. There is a white ribbon cable in front of it. You will need to remove the ribbon cable eventually, so you might as well do it now by pulling it out of the marked connector which does not have a locking mechanism. Then remove the screw.

On the bottom of the camera, there are two additional screws to remove that fasten the LCD to the body.

As a last step, before you can remove the LCD, there are 2 more ribbon cables to detach - marked in blue above. The one on the side has a locking mechanism that is unlocked by moving the two blue circled pieces of plastic in the direction in which the cable detaches.

The smaller one on the bottom can just be pulled out.

Once the LCD is removed the DIGIC processor board to the right ist last before we have access to the sensor. Start by detaching the additional 3 ribbon cables marked above. The green circled one just pulls out, the blue circled ones need to be unlocked first by flipping the black plastic flap on top of them open. Next, remove the screw circled red and you should be able to wiggle the DIGIC board out of the plastic holding it to the body.

Once it is loose, there is a tiny connector on top that needs to be detached.

Finally, on the back of the board there is another ribbon cable that needs to be disconnected before you can completely remove the board.

Now you have direct access to the CCD sensor of the camera. It is fastened by three TORX screws. The top left one will be covered by the piece of metal holding the flash capacitor. Just carefully bend it to the side and out of the way.

If you have not done so yet, make sure you have a well protected, dust free place to put the sensor while you remove the IR cut filter. Check the metal housing of the sensor to see if it might be secured by one or two small drops of glue. If so, carefully scratch the glue away with a screw driver or an exacto knife. Take extreme care not to cut or otherwise damage any of the ribbon cables. Then unfasten the screws and carefully lift the sensor off by its ribbon cable.

This is what the CCD sensor looks like after being detached.

Here you can see the slightly blue tinted IR cut filter that we will be replacing by an IR only filter. Before we proceed, take note of the 3 brass shims around the screw threads holding the sensor. Also, note the two small springs marked with red arrows above. You want to be extremely careful not to lose any of them.

Carefully pull off the rubber gasket around the IR cut filter with a pair of tweezers. Then, using a screw driver, pry off the IR cut filter which is held to the plastic beneath by 2 tiny drops of glue.

Once the IR cut filter has been removed, fabricate a replacement piece out of the Cokin P007 IR filter, or whatever material you will be using. If you do not replace the IR filter with something of similar thickness and refractive index, your camera will be extremely near sighted and unusable except maybe for macros.

Above you can see the original IR cut filter in blue. As I was unable to obtain a P007 IR pass filter on short notice, I used a P003 red filter for the replacement (seen to the right) and added a piece from a thin gelatin IR filter so it would still be IR only.

Install your filter replacement in the same spot that the IR cut filter occupied and secure it with 2 additional drops of an appropriate glue. Two tiny strips of tape will work as well. Now put back the rubber gasket around the filter and re-attach the CCD sensor carefully.

Congratulations, you are almost done! Now you only need to put the whole thing back together again by retracing your steps and assembling in reverse order. Pay specific attention when re-attaching all those ribbon cables and other connectors. You want them connecting the right way around, coming together again securely and locked in place where supported. All the while you do not want to exert excessive force on any of them. Check each connection thoroughly before you move on. I would guess that 90% of the problems you might have on reassebly will be bad connections.

Good luck!!!

I would like to thank the creators of the following 2 web sites, which proved invaluable resources the first time I attempted this modification:
I would further like to thank Thomas, who sacrificed his Powershot A80. Thanks also go to Iain, who's A70 was apparently not harmed during the making of this documentation.

Feedback and questions are highly welcome, feel free to leave a comment below.


路人癸 said...

Hi there, thanks for your very detailed guide to disassembling a PowerShot A70! I am following your instructions to attempt the same thing on my A80, which has the same construction save for the flippable LCD screen. I am now stuck at the last step; how did you remove the IR blocking filter from its seat? The glue is so hard I ended up chipping the filter itself. I wanted to use a glue gun to melt the glue but the gun head was too large. Maybe I should try heating up my screw driver?

Also, I have bought a Cokin P007 filter, which has a plastic ring around it. What is the best way to dismantle the Cokin filter and cut the IR passing filter to size? I heard that cutting the filter might cause it to shatter, and I want to make sure I don't flush my $70 down the drain.

Simon said...

I have just cme across this tutorial.
I plan to do a similar modification. I would like to ask you some questions concerning the replacement filter. Can I ask you this question here or maybe I can e-mail you?

Hope you'll see this comment :-)


Zara said...

Hello 路人癸,

I'm not sure I can help you with the IR cut filter. It was easily removable with the two A70's I modified. I'm not even sure if there was any glue involved, it may have just been held by the rubber gasket as seen here.

Regarding cutting of the P007 filter, I believe the instructions at the following web site are pretty good:

Zara said...

Simon, please feel free to post your questions as comments here, this way anyone else stopping by will benefit from them :-)

TP said...

very interesting, is the same set-up possible for UV only pics?

Anonymous said...


Great tutorial. Thanks for posting it.

Question: How thick is the original IR cut filter?

I have an Canon S330 I'd like to modify. I've been able to get to the CCD holder in back, which looks identical to yours. It's possible the IR cut filter is the same too. It would help to get an idea of how thick a replacement I need, before I open it up and expose it to dust.


Dian said...


Thank you for the thorough procedure write up. I'm performing the same replacement for a Canon powershot A75 but am having problems with the filter dimensions. Assuming the IR cut filter dimensions are the same for both camera models, would you know the dimensions to your IR cut filter? Or maybe, would you know of any sites that might sell these IR pass filters with the dimensions that the cameras require? Thanks.


Anonymous said...

My specific interest is Hydrogen alpha line
(defined as 656.3 nm) for astrophotography. I have a Canon Powershot A85, which seems to be the last that had fully automatic mode (settings are saved). Interesting point that amateur
astroonomers make such modifications, but so
far I have never seen a spectral scan of any
Powershot IR filter so the World can see if it
even blocks this wavelength to begin with. Much
above this wavelength won't matter for astrophotography because the atmosphere itself
is a filter. I therefore wonder if anyone has
done a wavelength scan, or if someone would be
willing to send one my way (I have equipment).
In this case, I would be happy to post the result.


Anonymous said...

Hey, great project.

I opened up my camera, carefully labelled the parts, until I got to the third last step. Then I found that my TORX screwdriver set was not small enough to fit the screws!

Does anyone have any advice on how to get them undone without buying mini TORX screwdrivers?

Thanks in advance

Electrician Toronto said...

Hi thanks so much for sharing your helpful guide!

SeeStimme said...

A question: When i dont put a Filter an the CCD Sensor, but on the Lins in front of the Cam. Works this?
Or can i put a low IR Filter on the CCD Modul and a second IR Filter on the Lins of the Cam.

So i can use a Filter 500 to 900. Not Only one Filter

Adel_7 said...

Superb guide! Thank You Very Much

Anonymous said...

i shocked myself 3 times when i touched the capacitor. i can tell you that the shock is pretty nasty.

Anonymous said...

Hi, would you happen to know where I could source the Canon A70 adjustment software that is used by Canon service centres. I haves replaced a CCD on my Canon A70 successfully but back focus is now out which can be sorted with this software.
Many thanks